Server maintenance is scheduled for Saturday, December 21st between 6am-10am CST.

During that time, parts of our website will be affected until maintenance is completed. Thank you for your patience.

Menu
Search
Filters
Close
Menu

Adhesion Failure Mode Analysis: Cyclic Peel Testing in Synthetic Sea Water

Adhesion Failure Mode Analysis: Cyclic Peel Testing in Synthetic Sea Water
Available for download

In this paper, I will discuss such an example of when the predicted service of the coating determines that a more dynamic method must be utilized. I will discuss testing that was conducted for immersion service where flow of water over the surface was a major consideration. The question of how well the adhesion would hold up in real life service could not be properly answered by the degree of failure in this case. I discovered that the more important consideration was the survivability of the coating if a defect were introduced.

Product Number: 41209-482-SG
Author: Ray Holden
Publication Date: 2009
Industry: Coatings
$0.00
$20.00
$20.00

Adhesion is a very important consideration in adhesives and coatings. Many of the methods commonly used to measure coating failure deal with the degree to which loss of adhesion occurs. A force is applied on a bonded film at a predetermined rate and the degree to which it fails is then quantified in some manner. In this scenario, two inches of peel is worse than one inch of peel. The more material that can be removed by the applied force, the better predictor of future coatings failure the method produces. When selecting a dynamic adhesion testing method, the degree of coating failure may not be as important as where the failure takes place within a coating system. Careful consideration of the mode of failure needs to be given in order to provide a complete predictor of failure over time. In this paper, I will discuss such an example of when the predicted service of the coating determines that a more dynamic method must be utilized. I will discuss testing that was conducted for immersion service where flow of water over the surface was a major consideration. The question of how well the adhesion would hold up in real life service could not be properly answered by the degree of failure in this case. I discovered that the more important consideration was the survivability of the coating if a defect were introduced.

Adhesion is a very important consideration in adhesives and coatings. Many of the methods commonly used to measure coating failure deal with the degree to which loss of adhesion occurs. A force is applied on a bonded film at a predetermined rate and the degree to which it fails is then quantified in some manner. In this scenario, two inches of peel is worse than one inch of peel. The more material that can be removed by the applied force, the better predictor of future coatings failure the method produces. When selecting a dynamic adhesion testing method, the degree of coating failure may not be as important as where the failure takes place within a coating system. Careful consideration of the mode of failure needs to be given in order to provide a complete predictor of failure over time. In this paper, I will discuss such an example of when the predicted service of the coating determines that a more dynamic method must be utilized. I will discuss testing that was conducted for immersion service where flow of water over the surface was a major consideration. The question of how well the adhesion would hold up in real life service could not be properly answered by the degree of failure in this case. I discovered that the more important consideration was the survivability of the coating if a defect were introduced.

Product tags
Also Purchased
Adhesion Tests and Failure Modes Study on Structural Steel Coatings
Available for download

Adhesion Tests and Failure Modes Study on Structural Steel Coatings

Product Number: 41213-771-SG
Author: Wei Zheng, John J. Myers
Publication Date: 2013
$20.00

Pull-off adhesion behaviors of 15 coating systems in three groups were studied utilizing test method ASTM D4541. Three groups of coating systems included coating systems with organic or inorganic zinc-rich primers, polymeric polyurea coatings, and overcoating systems applied on an existing coating system. 
A Study of the Effect of Film Thickness and Blast Profile on Accelerated Underfilm Corrosion Creep
Available for download

A Study of the Effect of Film Thickness and Blast Profile on Accelerated Underfilm Corrosion Creep

Product Number: 41213-779-SG
Author: Carl W. Reed
Publication Date: 2013
$20.00

The creepage of corrosion underneath a coatings film applied to a steel test panel is often used as a performance test for the anti-corrosion properties of a coating system. Underfilm corrosion creep, also sometimes referred as scribe creep in the laboratory environment, is defined as the degree of corrosion emanating away from a scribe line underneath a coating film applied to a steel substrate. 
Adhesion Measurements of Coatings on Cylindrical Steel Pipes: Variability & Significance
Available for download

Adhesion Measurements of Coatings on Cylindrical Steel Pipes: Variability & Significance

Product Number: 41214-815-SG
Author: S. G. Croll, B. D. Keil
Publication Date: 2014
$20.00

Quality assurance of coatings on steel water pipes commonly relies on tensile pull-off measurements of the coating-steel adhesion, according to ASTM D4541. These tests are performed by adhering a metal ‘dolly’ to the coating with an adhesive, then scoring around the dolly circumference, through the coating down to the steel surface, before recording the stress necessary to pull the dolly (and coating) away from the steel pipe. 
Categories
Industry
Recently viewed
Popular tags
View all

Association for Materials Protection and Performance

© AMPP All Rights Reserved.
Membership Terms of Content Use
Contact Customer Support