AMPP Store - Products tagged with 'Standards Benefit For Members'

Available for download

AMPP TR21499-2022, Currently Used Procedures for Dry Film Thickness Measurement and Recording for Coatings on Railcars

Product Number: AMPP TR21499-2022

Publication Date: 2022

$109.00

This AMPP technical report is intended for use by North America-based rail car manufacturers, owners, operators, and repairers who are seeking guidance concerning DFT measurement of coatings applied to rail cars.

Available for download

AMPP TR21500-2022, Surface Preparation by Encapsulated Blast Media for Repair of Existing Coatings on Railcars

Product Number: AMPP TR21500-2022

Publication Date: 2022

$109.00

This technical report provides practical information on the use of encapsulated blast media for repairing existing interior and exterior coatings on railroad tank cars (hereafter referred to as tank cars). This report: 1) introduces the technology; 2) describes typical abrasives, equipment, and processes used; and 3) provides a comparison to some other coating repair surface preparation methods typically used in the rail industry.

Available for download

AMPP TR21505-2022, Adverse Impacts of Wildfires on Power Industry Steel Structures

Product Number: AMPP TR21505-2022

Publication Date: 2022

$109.00

The purpose of this report is to communicate the effects of wildfires heat and combustion products on corrosion resistance, material properties, and mechanical integrity of power transmission infrastructure and to identify next steps to research, develop, and implement future asset integrity management actions for the power industry. The report addresses the following general topics.

Wildfire vulnerabilities and impacts
Materials effects for steel, coatings, and concrete
Power infrastructure risks and impacts
Asset integrity risk assessment guidance
Recommended industry actions
AMPP activities proposed

A wildfire, bushfire, wildland fire or field fire is an unplanned, unwanted, and usually uncontrolled event in an area of combustible vegetation. Due to climate change, many locations in the United States and worldwide, such as Australia and even India, are subject to wildfires due to dry conditions during parts of the year.

Available for download

AMPP TR21524-2023, Commentary on Standards Development for Selection and Qualification of HSC-Resistant Materials in Subsea Service with Cathodic Protection

Product Number: AMPP TR21524-2023

Publication Date: 2023

$109.00

As a companion document to MR21525, this Technical Report provides results, review and commentary on many investigations of HSC and includes important literature data, references, background information, service experience and related standards that were utilized in the development of the AMPP MR21525. Most of the information in this Technical Report covers findings from HSC field experience and HSC data from brine/CP exposure tests or from other cathodic charging experiments. It is important to note, in the use of MR21525 and in the review of data contained herein, that HSC can also be induced from hydrogenating environments and conditions other than from just from CP exposure alone. A non-exhaustive list of such conditions is presented later in this Technical Report.

Available for download

AMPP TR21527-2023, Corrosion and Protection of Tank Cars in Crude Oil Service

Product Number: AMPP TR21527-2023

Publication Date: 2023

$109.00

This AMPP technical report describes the current state of protecting the interiors of tank cars transporting crude oil. This report is intended for and will benefit all stakeholders involved in the protection of tank cars transporting crude oil, including large fleet tank car owners, crude oil coating suppliers, tank car coating applicators, and crude oil shippers. The current state of protecting the interiors of tank cars transporting crude oil was developed by conducting surveys of various stakeholders. This report summarizes the survey results.

Available for download

AMPP TR21540-2022, Correlating Qualitative Surface Profile Assessment Methods to Quantitative Methodology on Prepared Concrete Substrates

Product Number: AMPP TR21540-2022

Publication Date: 2022

$109.00

Coating/lining manufacturers and/or facility owners frequently specify cleaning and roughening of the concrete surface prior to product installation. The specifications may reference qualitative methods including visual assessments using comparison coupons or quantitative methods including surface profile depth measurements. However, prior to this Technical Report, there was no known data to inform a conversion between qualitative and quantitative methods. The outcomes of this Technical Report enable coating manufacturers, engineers, specifiers, and contractors to convert well-established qualitative methods to quantitative values based on an interlaboratory experiment. While current quantitative methods can measure up to 6 mm (250 mils), extremely rough concrete surfaces (exceeding ~1.5 mm, or ~50 mils) were not included in the experiment due to the inability to stabilize the instrument probe and obtain accurate data.

Available for download

AMPP TR21544-2022, Corrosion and Mitigation Techniques for Fire Protection Piping Systems

Product Number: AMPP TR21544-2022

Publication Date: 2022

$109.00

This report explains different types of corrosion phenomena and contributing factors of corrosion that can occur in fire protection systems (FPS), such as water corrosivity, MIC, trapped air (wet systems), residual water (dry systems), and pipe weld corrosion. The basis for selection of corrosion mitigation strategies for corrosion mitigation and management of FPS are also discussed.

Corrosion that results in pipe leakage or obstruction is the most significant issue for owners of water-based FPS or fire sprinkler systems, in terms of both cost and system reliability. Corrosion damage/products and mineral deposits can impair the effectiveness of sprinkler systems, leaving facilities vulnerable to uncontrolled fire loss even though they are equipped with fire protection systems. This report describes practices that have been successful in mitigating FPS corrosion.

Available for download

ANSI/NACE No. 13/SSPC-ACS-1-2016, Industrial Coating and Lining Application Specialist Qualification and Certification

Product Number: 21122-SG

ISBN: 1-57590-215-X

Publication Date: 2015

$109.00

Requirements for qualification of an industrial coating and lining application specialist that includes surface preparation and coating application for steel and concrete surfaces of industrial structures.

Available for download

ANSI/NACE SP0508-2017, Methods of Validating Equivalence to ISO 8502-9 on Measurement of the Levels of Soluble Salts

Product Number: 21134-SG

ISBN: 1-57590-222-2

Publication Date: 2017

$109.00

The Bresle patch method is defined by ISO 8502-9. This standard establishes the equivalence of other methods for measuring the level of contamination of salts to results of that same Bresle patch method.

Available for download

ANSI/NACE TM0284-2016, Evaluation of Pipeline and Pressure Vessel Steels for Resistance to Hydrogen-Induced Cracking

Product Number: 21215-SG

ISBN: 1-57590-163-3

Publication Date: 2016

$109.00

Test conditions for evaluation of pipeline and pressure vessel steels. Compares test results from different laboratories of the absorption of hydrogen generated by corrosion of steel in wet H2S.

Available for download

Application Process for Optimum Paint and Coating Systems’ Performance for Navy Ships

Product Number: SP21416-2020

Publication Date: 2020

$109.00

This NACE/EFC standard is considered as the basis for the cleaning, surface preparation, and application of paint and coating systems to Navy ships used in marine environments for New Build, and during Life Cycle maintenance and permanent repair. It is intended for use by naval corrosion control personnel, coating applicators, and coating manufacturers. It covers coating materials, coating test protocol and acceptance criteria, surface preparation, coating application, quality assurance and control, and repair methods. Its purpose is to facilitate more effective corrosion protection of Navy ships and support inter-operability requirements by presenting reliable information and providing guidelines for coating manufacturers and shipyards to develop more durable specifications.

This standard replaces NATO Allied Engineering Publication (AEP) 59.

Guide Specification for Application of Coating Systems with Zinc-Rich Primers to Steel Bridges

Product Number: SSPC-PA Guide 13-2014-AASHTO NSBA S8.1-2014

Publication Date: 2014

$0.00

Products tagged with 'Standards Benefit For Members'

Association for Materials Protection and Performance