Server maintenance is scheduled for Saturday, December 21st between 6am-10am CST.

During that time, parts of our website will be affected until maintenance is completed. Thank you for your patience.

Menu
Search
Filters
Close
Menu

Experimental and Numerical Studies on the Influence of Particle Sizes on Erosion of Elbows in Series in Gas-Solid and Multiphase Flow Conditions

Picture for Experimental and Numerical Studies on the Influence of Particle Sizes on Erosion of Elbows in Series in Gas-Solid and Multiphase Flow Conditions
Available for download

In the oil and gas industry, solid particle erosion is a common challenge in pipelines, flowlines, and fitting components such as elbows. Elbows have been widely used to change the flow direction in industrial flowlines. When erosion occurs due to the impact of solid particles, it leads to significant financial and environmental threats.

Product Number: 51323-19098-SG
Author: Mazen M. Othayq, Faris S. Bilal, Farzin Darihaki, Ronald E. Vieira, Soroor Karimi, Siamack A. Shirazi
Publication Date: 2023
$0.00
$20.00
$20.00

Elbows in series are commonly encountered in various piping systems on oil and gas subsea platforms. In numerous oil and gas fields, solid particles are entrained with produced fluid causing solid particle erosion of these elbows. Therefore, solid particle erosion was examined in two standard ID 3-inch (76.2 mm) elbows in series. The distance between the two elbows is twice the pipe diameter (2D). Firstly, paint removal studies were performed to identify the location of the maximum erosion in the second elbow with superficial gas (air) and liquid (water) velocities of 31 m/s and 0.1 m/s, respectively, using 300 and 75 μm particle sizes. Secondly, erosion measurements were conducted in two standard stainless-steel (SS316) elbows with 25, 75, and 300 μm particle sizes. The results of the erosion measurement in the annular flow condition were compared with the gas-solid flow with a gas velocity of 31 m/s and particle sizes of 300 and 75 μm. The paint removal experimental studies showed that the location of the maximum erosion changes with changing the particle sizes in the second elbow. The erosion measurements showed that the erosion ratio (2nd elbow/1st elbow) in gas-solid is higher than in annular flow conditions by a factor of 14.25 and 5.8 with 75 and 300 μm particle sizes, respectively. Also, Computational Fluid Dynamics (CFD) simulations were performed for gas-sand flow conditions with 31 m/s gas velocity to study the effect of particle size on erosion in the investigated elbows. The CFD results over-predicted the erosion ratio (2nd elbow/1st elbow) by a factor of around 2.1 and 2.4 for 75 and 300 μm particle sizes, respectively.

Elbows in series are commonly encountered in various piping systems on oil and gas subsea platforms. In numerous oil and gas fields, solid particles are entrained with produced fluid causing solid particle erosion of these elbows. Therefore, solid particle erosion was examined in two standard ID 3-inch (76.2 mm) elbows in series. The distance between the two elbows is twice the pipe diameter (2D). Firstly, paint removal studies were performed to identify the location of the maximum erosion in the second elbow with superficial gas (air) and liquid (water) velocities of 31 m/s and 0.1 m/s, respectively, using 300 and 75 μm particle sizes. Secondly, erosion measurements were conducted in two standard stainless-steel (SS316) elbows with 25, 75, and 300 μm particle sizes. The results of the erosion measurement in the annular flow condition were compared with the gas-solid flow with a gas velocity of 31 m/s and particle sizes of 300 and 75 μm. The paint removal experimental studies showed that the location of the maximum erosion changes with changing the particle sizes in the second elbow. The erosion measurements showed that the erosion ratio (2nd elbow/1st elbow) in gas-solid is higher than in annular flow conditions by a factor of 14.25 and 5.8 with 75 and 300 μm particle sizes, respectively. Also, Computational Fluid Dynamics (CFD) simulations were performed for gas-sand flow conditions with 31 m/s gas velocity to study the effect of particle size on erosion in the investigated elbows. The CFD results over-predicted the erosion ratio (2nd elbow/1st elbow) by a factor of around 2.1 and 2.4 for 75 and 300 μm particle sizes, respectively.

Product tags
Also Purchased
Picture for Material Selection for Carbon Capture and Storage (CCS) Wells
Available for download

Material Selection for Carbon Capture and Storage (CCS) Wells

Product Number: 51323-18760-SG
Author: Willem Maarten van Haaften, Hisashi Amaya, Bostjan Bezensek, Yuji Arai, Brian Chambers, Hiroki Kamitani
Publication Date: 2023
$20.00

The goal of the Paris Agreement is to limit global warming to below 2°C, preferably 1.5°C, compared to pre-industrial levels.1 While the world is slowly transitioning to more sustainable energy sources to reach this target, one of the ways to reduce the CO2 in the atmosphere is to capture it and store it in depleted gas fields. According to the IOGP1, the total number of CCS projects in Europe is 65 in 2022.2 The aim of these projects is to store around 60 MtCO₂/yr by 2030.
Picture for A Comparative Study on Coating Performance of Inorganic Zinc Primer System and Inorganic Copolymer System by Long-Term Durability Test Including High Temperature Exposure at 540℃
Available for download

A Comparative Study on Coating Performance of Inorganic Zinc Primer System and Inorganic Copolymer System by Long-Term Durability Test Including High Temperature Exposure at 540℃

Product Number: 51323-18820-SG
Author: Chuljung Kim
Publication Date: 2023
$20.00

Bulk items such as cast and forged valves are installed under various temperature conditions. It is exposed to a wide range of temperatures, therefore the coating product applied to bulk items should have appropriate heat resistance performance. However, it is very difficult to select a suitable coating system since the temperature condition is not determined in the valve manufacturing stage. For this reason, unsuitable coating systems are often applied, causing coating defects in the field operation. Therefore, it is necessary to apply a coating system that can cover a wide temperature range to prevent this problem.
Picture for Pressure Vessel Thickness Monitoring and Analyzing Using Linear Regression and Control Chart
Available for download

Pressure Vessel Thickness Monitoring and Analyzing Using Linear Regression and Control Chart

Product Number: 51323-18821-SG
Author: Chen Shao-Chi, Hsieh Cheng-Hsuan
Publication Date: 2023
$20.00

Metal loss due to corrosion is a universal phenomenon in refineries which could in turn cause leakage or explosion if not well monitored. There are several units in a refinery such as crude distillation unit, hydro-processing unit, acid alkylation unit, etc. In each unit, there are hundreds of pressure vessels which have different potential damage mechanisms. Hence, it’s critical to establish an effective and efficient way to monitor thickness changing behavior.
Categories
Industry
Recently viewed
Popular tags
View all

Association for Materials Protection and Performance

© AMPP All Rights Reserved.
Membership Terms of Content Use
Contact Customer Support