Server maintenance is scheduled for Saturday, December 21st between 6am-10am CST.

During that time, parts of our website will be affected until maintenance is completed. Thank you for your patience.

Search
Filters
Close

Search and Filter

Toggle Open/Closed
View as
Display per page
3440 total products found.
Picture for 01642 CORROSION PERFORMANCE OF EPOXY-COATED
Available for download

01642 CORROSION PERFORMANCE OF EPOXY-COATED

Product Number: 51300-01642-SG
ISBN: 01642 2001 CP
Author: Alberto A. Sagues, Rodney G. Powers and Richard Kessler
$20.00
Picture for Sour Service Limits of Martensitic SS: Review of Current Knowledge Test Methods and Development
Available for download

51313-02639-Sour Service Limits of Martensitic SS: Review of Current Knowledge Test Methods and Development

Product Number: 51313-02639-SG
ISBN: 02639 2013 CP
Author: Nacéra Sabrina Meck
Publication Date: 2013
$20.00
Picture for Effect of Steel Surface Roughness on Coating Performance
Available for download

Effect of Steel Surface Roughness on Coating Performance

Product Number: 51319-12830-SG
Author: Russell Draper
Publication Date: 2019
$20.00

This paper describes experimental work investigating the influence of steel surface roughness on the adhesion performance of fusion bonded epoxy (FBE) pipeline coatings. The paper begins with a summary of the standards and methods that can be used to measure surface roughness. Several parameters are used to characterize the roughness of a blast cleaned steel including profile peak height and peak count. Tortuosity and rugosity indicate the proportional increase in steel surface area developed by roughening the surface. Normal pipeline coating industry practice is to specify and control a single roughness parameter termed “surface profile”. It is measured with replica tape and corresponds to the maximum peak-to-valley height.In the experimental work steel panels were abrasive blast cleaned with various steel shot and grit abrasives and the roughness characteristics of the blast cleaned surface were measured with stylus profilometers conventional replica tape and 3D imaging of replica tape.A FBE pipeline coating was applied to the prepared steel panels. The adhesion performance of the FBE coating was evaluated using the following test methods.<ul><li>Hot water immersion adhesion rating per CSA Z245.20 section 12.14 </li><li>Pull-off adhesion strength after hot water soak exposure per ASTM 4541 </li><li>Cathodic disbondment radius at 65 and 80 °C per CSA Z245.20 section 12.8 </li><li>Time before blisters were observed in Atlas Cell per NACE TM0174 modified </li><li>Average blister diameter in Atlas Cell </li><li>Pull-off adhesion strength after Atlas Cell exposure per ASTM 4541 </li></ul>The experimental data were analyzed using statistical techniques to investigate the relationship between the measured surface roughness and the adhesion test results. The adhesion results were found to be positively and linearly correlated with substrate tortuosity and rugosity. Profile peak height and peak count were found to contribute to tortuosity.

Picture for 03132 TESTING OF SUPERDUPLEX STAINLESS
Available for download

03132 TESTING OF SUPERDUPLEX STAINLESS STEEL FOR SOUR SERVICE

Product Number: 51300-03132-SG
ISBN: 03132 2003 CP
Author: Paul Woollin, Manuel Maligas
$20.00
Picture for Magnetite Anodes for Deep Well Groundbeds
Available for download

51314-4470-Magnetite Anodes for Deep Well Groundbeds

Product Number: 51314-4470-SG
ISBN: 4470 2014 CP
Author: Torsten Krebs
Publication Date: 2014
$20.00
Picture for Corrosion Damage of Injection String From the Deep Geothermal Well IDDP-2 in Reykjanes Iceland
Available for download

Corrosion Damage of Injection String From the Deep Geothermal Well IDDP-2 in Reykjanes Iceland

Product Number: 51319-13247-SG
Author: Sigrun Karlsdottir
Publication Date: 2019
$20.00

The drilling of the second deep geothermal well drilled in the Iceland Deep Drilling Project (IDDP) at Reykjanes geothermal field was successfully completed in beginning of the year 2017. The previously drilled RN 15 production well 2500 m deep at the Reykjanes high temperature geothermal field was used as the base for the IDDP-2 well. The final depth of the IDDP-2 well reached 4650 m depth with a bottom hole temperature measured to be 427°C and a pressure around 340 bar. This made the bottom of the IDDP-2 well reach fluid at supercritical conditions and become the deepest geothermal well in Iceland. The well was then injected with coldwater for stimulation. During the injection the pumping was interrupted and the water in the well was able to heat up. When the injection string (pipe) was retrieved from the well extensive corrosion damages were apparent on the lowest part of the injection string. Cracks were also observed on a 500-meter interval of the injection string pipe starting from the bottom part. The injection string was visually inspected on-site and selected parts were chosen for further failure analysis. Specimens from the pipe and pipe connections were examined using an optical microscope scanning electron microscope (SEM) equipped with energy-dispersive X-ray spectroscopy (EDS) and X-ray diffraction (XRD) technique. This was done to investigate and discuss the most probably cause of the corrosion damages. Additionally the hardness of specimens of the pipe were measured and compared to the NACE MR 0175/ISO 15156 standard. This paper covers the procedure and results of the failure analysis of the injection string from IDDP-2 well.

Picture for 07037 Use of CP Coupons and Soil Corrosion Probes in Application of Pipeline Cathodic Protection Cri
Available for download

07037 Use of CP Coupons and Soil Corrosion Probes in Application of Pipeline Cathodic Protection Criteria

Product Number: 51300-07037-SG
ISBN: 07037 2007 CP
Author: Naeem A. Khan
Publication Date: 2007
$20.00
Picture for Corrosion Resistance and Mechanical Properties of a 140 ksi min Alloy 945X for HPHT Applications
Available for download

51312-01393-Corrosion Resistance and Mechanical Properties of a 140 ksi min Alloy 945X for HPHT Applications

Product Number: 51312-01393-SG
ISBN: 01393 2012 CP
Author: Sarwan K. Mannan
Publication Date: 2012
$20.00
Picture for Novel Slime Release Biocide Free Technology
Available for download

51314-4468-Novel Slime Release Biocide Free Technology

Product Number: 51314-4468-SG
ISBN: 4468 2014 CP
Author: Michael Winter
Publication Date: 2014
$20.00
Picture for 08005 Cathodic Disbonding of Epoxy Coatings - Effect of Test Parameters
Available for download

08005 Cathodic Disbonding of Epoxy Coatings - Effect of Test Parameters

Product Number: 51300-08005-SG
ISBN: 08005 2008 CP
Author: Ole Øystein Knudsen, and Jan Ivar Skar
Publication Date: 2008
$20.00
Picture for Corrosion Control System Performance for Large Diameter Water Mains in a Light -Rail and Interstate
Available for download

51314-4008-Corrosion Control System Performance for Large Diameter Water Mains in a Light -Rail and Interstate

Product Number: 51314-4008-SG
ISBN: 4008 2014 CP
Author: Stuart Greenberger
Publication Date: 2014
$20.00